technology
Parameter Table

Specifications for Cone Fastening Connection Bushings

橡胶同步带产品简介
同步带采用氯丁橡胶、玻璃纤维绳和尼龙弹性布三种主要材料制成,传动是由一根内周表面设有等间距离的封闭环行胶带和相应的带轮所组成。工作时,带齿与带轮的齿槽相啮合,是一种啮合传动,因尔具有齿轮转动、链转动和带传动的各自优点。
本公司生产的同步带具有优良的耐屈挠性、伸长率小、强力高等优点,还具有耐油、耐老化、耐臭氧、抗龟裂等优良性能。

BRIEF INTRODUCTION

Timing belt is composed of a closed round rubber with teeth and attached belt or pulley, when working,teeth and trough is interlocking.One movement will cause transmission of teeth, chain and belt.
"Fulong" brand timing belt's advantage are anti-wearing out,small elongation rate and strong,also,it is a nti-oil,antiheat, anti-ageing.Anti-ozone.

同步带的保管、安装使用注意事项
1、严禁将皮带强行过度折断、弯曲、避免强力层损伤,失去使用价值;
2、不得将皮带长期处于不正常的弯曲状态存放;
3、保存在阴凉处,一般温度为-15度---50度,并距热源至少一米以外;
4、安装时请缩短中心距,放松张紧轮,不得强行将带从凸挡边上硬拉拖磨装入;
5、带轮的齿必须与逞的运转方向直角。
6、主动轮与被动轮的主轴的平行度应控制在正切tg=1/1000左右。轴位不准,直接影响使用寿命。
7、发现主动轮上皮带向一边偏位,应移动一下被动轮加发调整,并调整张紧轮的压力;
8、在起动时,中心距改变,皮带松驰,发生跳齿现象,应检查带轮架是否松动,轴的定位有否失准,加以调整、加固;
9、同步带安装时必须按不同的型号和带宽适当的加以张紧力;
10、张紧轮且一定要安装在带动的传动松边一侧。

PRECAUTONS FOR STORAGE,INSTALLATION AND USE
1. Excessive bending and folding by force of this rubber belt is rigidly forbidden to avoid the damage of the dynamic stratum.
2. Long-time storage of this belt in an abnormally bended status is forbidden.
3. To be stored in a cool place.
4. Shorten the distance between the two whell centers, loosen the tensile wheelinstall this belt, it is absultely hazardous to set it onto the wheel through the latter s flange tu force.
5. Be sure to keep the wheel teeth at an 90 angle against the moving direction of the band.
6. Besure that the parallel between the spindles of the driving and driven wheels is at tg=1/0000 lor so.
7. In case the band on the driving wheel deviates to one side, adjustment should be done only after shifting the driven wheela little. At the same time regulate the pressure of the tensile wheel.
8. Check whether either wheels holder slakens or there is any inaccuracy of either wheels position in case the distance between the two centers changers. The band losens and jumps over the dentation. Then tightenup and correct accordingly.
9. Give a proper tensile force according to type and width of the beltwhen install the band.
10. The tensile wheel should be mounted on the belt s slack edge.

whatsapp facebook instagram wechat